进口导热油泵-进口油泵-德国KAYSEN泵业

进口导热油泵-进口油泵-德国KAYSEN泵业

产品介绍:

进口导热油泵-油泵-德国KAYSEN泵业 GERMANY KAYSEN PUMP CO .,LTD 进口导热油泵采用自热散热结构,改变了传统的水冷却结构,使结构简单,体积小,节约运行费用,性能好,使用可靠,基本结...


  • 物品单位:
  • 品牌: KAYSEN
  • 货号: KS5893569

产品详细说明

品牌 KAYSEN
货号 KS5893569
用途 抽水、化工、制药、石油、冶金、染料、冶炼、电力、电镀、农药、造纸、食品、纺织等行业酸洗工艺、制酸制碱、喷漆工艺、有色金属冶炼中的电解液输送、离子膜项目中的氯水输送、废水处理、电镀、农药领域。
型号 KAYSEN
工作压差 0
压力环境 常压
介质温度 250℃
驱动方式 电动
适用介质

进口导热油泵-油泵-德国KAYSEN泵业

GERMANY KAYSEN PUMP CO .,LTD

进口导热油泵采用自热散热结构,改变了传统的水冷却结构,使结构简单,体积小,节约运行费用,性能好,使用可靠,基本结构形式为单级单吸悬臂式脚支撑结构,泵的为轴向吸入,出口为中心垂直向上,和电机同装于底座上。 导热油泵的支撑采用了双端球轴承支撑的结构形式,前端采用润滑油润滑,后端采用润滑脂润滑,中间有一导油管,用以随时观察密封情况和回收导热油。


进口导热油的材质选择决定耐温:
进口导热油泵全部都采用铸钢材质,铸钢含锰 11%~14%的高猛钢能耐冲击磨损,多用于矿山机械、工程机械的耐磨零件用在有腐蚀或者650℃以上高温条件下工作的零件,如化工用阀体、泵、容器或者大容量电站的汽轮机壳体等。保证导热油泵在高速、高温情况的长时间运转。其材质采用普通生铁铸件来替代导热油泵的泵体及叶轮材质,这样做是*不可以的,本身导热油泵使用温度就很高,生铁铸件一旦遇冷就会有产生爆炸的危险。 导热油泵材质 所以泵的安全隐患真的很大。提醒各各个使用厂家要提高重视,同时经过一些不正规厂家立即停止这种不道德而且危险的作为。导热油泵就是一种理想的热油循环泵或者作载热体输送泵,是热交换设备上比较理想的配套用泵。 磁力驱动无泄漏热油泵在原有泵的基础上改进密封工艺采用永无泄漏高温磁力密封使导热油泵终身无泄漏,电机轴和导热油泵泵轴没有接触、无摩擦,所以导热油泵在运转中比普通导热油泵噪音低的多、更加平稳、使用寿命更长,阻绝了以往导热油泵跑、冒、滴、漏的现象。同样使用温度能达到≤400℃。



主要特点:

采用填料密封和机械密封相结合的形式,填料密封用耐高温的填料,具有良好的热态适应性,而机械密封则采用机械强度高,耐磨性好的硬质合金材料,保证了高温情况下的密封性能。

采用聚四氟乙烯(简称PTFE)做唇形密封,使密封性能产生了飞跃,比橡胶类密封可靠性提高25倍,耐腐蚀性能极强。


主要应用:

导热油泵的技术先进、效率高,在热的状态下可以长期稳定运转并且无泄漏,无附加冷却系统,使用安全可靠等一系列特点,在我国的载热体加热系统中得到了广泛的应用,已经进入石油、制药、纺织、印染、化工、橡胶、塑料、筑路、食品等其他工业领域。


导热油泵的维护与保养:
导热油泵的技术先进、效率高,在热的状态下可以长期稳定运转并且无泄漏,无附加冷却系统,使用安全可靠等一系列特点,在我国的载热体加热系统中得到了广泛的应用, 下面是凯森泵业为广大客户分析导热油泵保养维护小常识:导热油泵是国内外热循环交换设备中最不可以缺少的泵类传输推动设备,由于这个设备高速运转工作,使用量大,在整个热交换设备中属于容易损坏设备,虽说属于容易损坏设备,如果良好的保养和维护工作跟得上的话,照样可以使用的很长时间。 导热油泵使用虽然跟季节没有很大的关系,但连续工作一段时间以后(一般规定2000小时左右),定期更换泵体轴承腔里的润滑油,即可延长泵轴、轴承、密封地使用时间,导热油泵是叶轮式离心泵类产品,最核心运转部件就是轴承了,密封以及轴的加工精度,及时维护这几个部位地关键工作就是定期更换泵腔内润滑油,根据换掉的废润滑油能判断出导热油的质量以及内部杂质多少及密封磨损程度,以便于及时更换相对应的部件!

The heat-conducting oil pump adopts self-heating heat-dissipating structure, which changes the traditional water-cooling structure, makes the structure simple, small in size, saves operating cost, has good performance and is reliable in use. The basic structure is a single-stage single-suction cantilever foot support structure, and the pump is imported. For axial suction, the outlet is centered vertically upwards and mounted on the base with the motor. The support of the heat transfer oil pump adopts the structure supported by the double-end ball bearing. The front end is lubricated with lubricating oil, the rear end is lubricated with grease, and the middle end has a guide oil pipe for observing the sealing condition and recovering the heat transfer oil at any time.



The material selection of the heat transfer oil determines the temperature resistance:

The heat transfer oil pumps are all made of cast steel. The high-strength steel with 11%~14% manganese in cast steel can withstand impact and wear. It is used in the wear-resistant parts of mining machinery and engineering machinery for corrosion or high temperature operation above 650 °C. Parts, such as chemical valve bodies, pumps, containers, or turbine housings for large-capacity power stations. Ensure long-term operation of the heat transfer oil pump at high speed and high temperature. The material is made of ordinary cast iron castings instead of the pump body and impeller material of the heat transfer oil pump. This is absolutely impossible. The temperature of the heat transfer oil pump itself is very high. Once the cast iron castings are cold, there is a danger of explosion. Heat transfer oil pump material The safety hazard of the pump is really great. Remind each manufacturer to pay more attention, and at the same time, some unscrupulous and dangerous actions are immediately stopped by some informal manufacturers. The heat transfer oil pump is an ideal hot oil circulation pump or a heat carrier pump, which is an ideal matching pump for heat exchange equipment. The magnetic drive non-leakage hot oil pump improves the sealing process on the basis of the original pump. The non-leakage high temperature magnetic seal is used to make the heat transfer oil pump have no leakage for life. The motor shaft and the heat transfer oil pump pump shaft have no contact and no friction, so the heat transfer oil pump is more normal in operation. The heat transfer oil pump has much lower noise, more stable and longer service life, which prevents the phenomenon of running, running, dripping and leaking of the heat transfer oil pump. The same temperature can be used to reach ≤400 °C.




main feature:


●It adopts the combination of packing seal and mechanical seal. The packing is sealed with high temperature resistant filler and has good thermal adaptability. The mechanical seal uses high hardness and good wear resistance of hard alloy material to ensure high temperature. Sealing performance in case.


●Using imported PTFE (abbreviated as PTFE) for lip seal, the sealing performance has made a leap, the reliability of rubber seal is 25 times higher, and the corrosion resistance is extremely strong.




main application:


The heat transfer oil pump has advanced technology, high efficiency, long-term stable operation and no leakage in the hot state, no additional cooling system, safe and reliable use, and has been widely used in China's heating medium heating system. Has entered the petroleum, pharmaceutical, textile, printing and dyeing, chemical, rubber, plastics, road construction, food and other industrial areas.



Maintenance and maintenance of the heat transfer oil pump:

The heat transfer oil pump has advanced technology, high efficiency, long-term stable operation and no leakage in the hot state, no additional cooling system, safe and reliable use, and has been widely used in China's heating medium heating system. The following is the analysis of the maintenance and repair of the heat transfer oil pump for the customers of Germany Kaisen Pump Industry: the heat transfer oil pump is the most indispensable pump transmission and promotion equipment in the domestic and international thermal cycle exchange equipment. Because of the high speed operation of this equipment, the use amount is large. It is easy to damage the equipment in the whole heat exchange equipment. Although it is easy to damage the equipment, it can be used for a long time if good maintenance and maintenance work can be done. Although the use of the heat transfer oil pump has no great relationship with the season, after a period of continuous operation (generally 2,000 hours or so), the lubricating oil in the pump bearing cavity can be replaced regularly to extend the use time of the pump shaft, bearing and seal. The heat transfer oil pump is an impeller centrifugal pump. The core operating components are the bearing, the seal and the machining accuracy of the shaft. The key task of timely maintenance of these parts is to periodically replace the lubricating oil in the pump chamber. Can judge the quality of the heat transfer oil and the amount of internal impurities and seal wear, so as to replace the corresponding parts in time!

Cutting submersible sewage pump

Diving flow booster

Submersible mixed flow pump

Submersible return pump

Corrosion resistant sewage pump

Submersible mixer

位于Schw?bischGmünd的凯森Kaysen泵业有限公司是 *的各种流体水泵和隔膜泵制造商之一。60多年来,凯森以“制造”的可靠性和质量达到了*标准。凭借我们全面的产品组合,我们支持 各地的客户成功掌握供水,采矿,工业,化工,造纸,电力,食品,制药,污水和海上行业的苛刻抽水任务。作为上述领域创新技术的*供应商,我们是液体需要安全,高效和经济运输的*合作伙伴。

凯森始终坚持“重质量,讲信誉”为宗旨。产品现 全国各地,并已逐步开发海外市场。公司多次被评为“重合同讲信用”企业,深得用户的信赖和广泛的赞誉。

The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.