1
起批量(台) 价格
0 面议
供货能力: 电议 最低订购量: 1台
可销售总数量: 1000台
发布日期: 2019-10-12 更新日期: 2020-11-12
品牌: 德国KAYSEN 型号: KAYSEN
驱动方式: 电动 介质温度: 250 ℃
工作压差: 0 适用介质:
压力环境: 常压 货号: KS561058
用途: 抽水、化工、制药、石油、冶金、染料、冶炼、电力、电镀、农药、造纸、食品、纺织等行业酸洗工艺、制酸制碱、喷漆工艺、有色金属冶炼中的电解液输送、离子膜项目中的氯水输送、废水处理、电镀、农药领域。 外型尺寸:

进口喷泉泵-进口不锈钢喷泉泵-德国KAYSEN泵业

GERMANY KAYSEN PUMP CO .,LTD

喷泉专用泵,外壳、过流部件及外部零件材质均采用铸铁或者不锈钢(304、316、316L)制成的,并且该产品还保留了原来喷泉专用泵性能。开泵前,吸入管和泵内必须充满液体。开泵后,叶轮高速旋转,其中的液体随着叶片一起旋转,在离心力的作用下,飞离叶轮向外射出,射出的液体在泵壳扩散室内速度逐渐变慢,压力逐渐增加,然后从泵出口,排出管流出。


主要特点:

喷泉专用泵其外壳、过流部件及外部零件材质均采用铸铁或者不锈钢(304、316、316L)制成的,并且该产品还保留了原来喷泉专用泵性能。
采用铸铁或者不锈钢材料,提高泵的耐腐蚀性。
叶轮采用专用材料防止叶轮时叶轮松动。 喷泉专用泵
漏电保护措施:采用定电位接地装置。
在原普通泵的基础上,根据喷泉专用泵的要求,公司经 过多次试验,在技术上不断开发,加工材料上不断改进,使喷泉专用泵可以频繁起动,完全适合音乐喷泉的使用。
泵采用不锈钢滤网护罩,三相四线电缆。
不锈钢喷泉泵为自动注水功能。
该电机为自循环充水式冷却。

 

主要应用:
喷泉潜水泵主要用于喷泉供水,水产养殖等场所。广泛用于低扬程的城市、农田排 灌、喷灌,工业及民用的供、排水系统,丘陵、山区引水,以及低洼地排除积水。

喷泉泵故障排除法:
       1.启动时水泵不转 原因:填料太紧或叶轮与泵体之间被杂物卡住而堵塞;泵轴、轴承、泄漏环锈住;泵轴严重弯曲。排除方法:放松填料,疏通引水槽:拆开泵体清除杂物或锈;校正弯曲的轴或换新的泵轴。
  2.启动后水泵不出水 原因:泵内有空气或进水管积气;底阀关闭不严灌水不满、真空泵填料严重漏气;闸阀或拍门关闭不严。排除方法:清除杂物,更换已损坏的橡皮垫,改变阀片方向;压紧或更换新的填料,关闭闸阀或拍门;加大灌水量,直到放气螺塞处不冒气泡;更换有裂纹的管水;降低扬程,将水泵的管口压入水下0.5米。
  3.流量不足 原因:水泵实际扬程超过允许扬程;转速不配套或皮带打滑、转速偏低;轴流泵叶片安装角太小;吸程过高;底阀、管路及叶轮局部堵塞或叶轮缺损;出水管漏水严重。排除方法:降低扬程,恢复额定转速,清除皮带污垢并调好皮带紧度;调好叶片角,降低水泵安装位置;拧紧压盖、密封水泵漏水处,压紧填料或更换填料;清除堵塞物、更换叶轮;更换泄漏环,堵塞漏水处。
  4.流量由大变小 原因:滤网或喇叭口逐渐被杂物堵塞;动水位降低、进水管淹没水深不够。排除方法:清除杂物,加大底阀入水深度。
  5.运行中出水中断 原因:管路或进水处有杂物堵塞;填料磨损、松动、水封管堵塞;叶轮被打坏或松脱;动水位剧降。排除方法:清除堵塞物,更换填料、疏通引水管沟槽,正确安装水封环;紧固或更换叶轮;降低水泵安装位置,或待水位上升后再开机。
  6.功率消耗太大 原因:转速过高;泵轴弯曲;叶片绕有杂物;扬程过高。排除方法:调整合适的转速;校正泵轴;清除杂物;设法降低扬程。

喷泉泵日常维护:
(1)检查并处理易于松动的螺栓或螺母。如拍门、螺栓、轴销、销钉等,双吸离心泵轴封装置填料的松紧程度,空气压缩机阀片等。
(2)油、水、气管路接头,阀门渗漏处理。
(3)电动机碳刷、滑环、绝缘等的检查处理。
(4)检查拦污栅前有无阻水杂物。
(5)保持电动机干燥,检查电动机绝缘。
(6)检修闸门吊点是否牢固,门侧有无卡阻物、锈蚀及磨损情况。
(7)闸门启闭设备维护。
(8)吊车维护。
(9)机组设备清洁。




The special pump for the fountain, the outer casing, the over-current parts and the external parts are made of cast iron or stainless steel (304, 316, 316L), and the product retains the original pump-specific pump performance. The suction tube and pump must be filled with liquid before the pump is turned on. After the pump is turned on, the impeller rotates at a high speed, and the liquid rotates with the blade. Under the action of the centrifugal force, it flies outward from the impeller, and the liquid that is ejected in the pump chamber diffuses slowly, the pressure gradually increases, and then the pump At the exit, the discharge pipe flows out.



main feature:


The fountain pump has its outer casing, over-current parts and external parts made of cast iron or stainless steel (304, 316, 316L), and the product retains the original pump-specific pump performance.

●Use cast iron or stainless steel to improve the corrosion resistance of the pump.

●The impeller uses special materials to prevent the impeller from loosening when the impeller is used. Fountain special pump

● Leakage protection measures: Use a constant potential grounding device.

● On the basis of the original ordinary pump, according to the requirements of the special pump for the fountain, the company has undergone many tests and continuously developed in technology, and the processing materials have been continuously improved, so that the special pump for the fountain can be started frequently, which is completely suitable for the use of the musical fountain.

●The pump adopts stainless steel strainer shield and three-phase four-wire cable.

● Stainless steel fountain pump is automatic water injection function.

● The motor is self-circulating and water-cooled.


 


main application:

The fountain submersible pump is mainly used in fountain water supply, aquaculture and other places. It is widely used in low-lift cities, farmland irrigation, sprinkler irrigation, industrial and civil supply and drainage systems, water diversion in hills and mountains, and low-lying water.


Fountain pump troubleshooting method:

       1. The pump does not turn when starting. Cause: The packing is too tight or the impeller and the pump body are stuck by the debris; the pump shaft, the bearing and the leakage ring are rusted; the pump shaft is severely bent. Remedy: Dissipate the packing and clear the drain: Disassemble the pump to remove debris or rust; correct the bent shaft or replace the pump shaft.

2. The pump does not produce water after starting. Cause: There is air in the pump or water in the inlet pipe; the bottom valve is not tightly filled with water, the vacuum pump packing is seriously leaked; the gate valve or the door is not closed. Remedy: remove debris, replace the damaged rubber mat, change the direction of the valve; press or replace the new filler, close the gate valve or flap the door; increase the amount of water until the venting plug does not bubble; replace Cracked pipe water; reduce the lift and press the nozzle of the pump into the water 0.5 m.

3. Insufficient flow: The actual lift of the pump exceeds the allowable lift; the speed is not matched or the belt slips and the speed is low; the installation angle of the axial pump blade is too small; the suction stroke is too high; the bottom valve, pipeline and impeller are partially blocked or impeller defect The outlet pipe is leaking seriously. Remedy: reduce the lift, restore the rated speed, remove the belt dirt and adjust the belt tightness; adjust the blade angle to reduce the pump installation position; tighten the gland, seal the water pump leakage, press the packing or replace the packing; remove the blockage, Replace the impeller; replace the leak ring and block the leak.

4. The flow rate is changed from large to small. Cause: The filter or bell mouth is gradually blocked by debris; the moving water level is lowered, and the water inlet is submerged. Remedy: Remove debris and increase the depth of the bottom valve.

5. Intermittent water outage during operation Cause: There is debris in the pipeline or water inlet; the packing is worn, loose, and the water sealing tube is blocked; the impeller is broken or loose; the water level drops sharply. Remedy: remove the blockage, replace the packing, clear the groove of the water pipe, install the water seal ring correctly; tighten or replace the impeller; reduce the installation position of the water pump, or turn the water on after the water level rises.

6. Power consumption is too large Cause: The speed is too high; the pump shaft is bent; the blade is surrounded by debris; the lift is too high. Remedy: Adjust the appropriate speed; calibrate the pump shaft; remove debris; try to lower the lift.


Fountain pump daily maintenance:

(1) Inspect and handle bolts or nuts that are easy to loosen. Such as shooting doors, bolts, axle pins, pins, etc., the double-suction centrifugal pump shaft sealing device packing tightness, air compressor valve and so on.

(2) oil, water, gas pipeline joints, valve leakage treatment.

(3) Inspection and treatment of motor carbon brushes, slip rings, insulation, etc.

(4) Check for water-blocking debris before the trash rack.

(5) Keep the motor dry and check the motor insulation.

(6) Check whether the lifting point of the gate is firm, and there is no jam, rust and wear on the door side.

(7) Maintenance of gate opening and closing equipment.

(8) Crane maintenance.

(9) The unit equipment is clean.

       位于德国Schw?bischGmünd的凯森Kaysen泵业有限公司是世界*的各种流体水泵和隔膜泵制造商之一。60多年来,凯森以“德国制造”的可靠性和质量达到了*标准。凭借我们全面的产品组合,我们支持世界各地的客户成功掌握供水,采矿,工业,化工,造纸,电力,食品,制药,污水和海上行业的苛刻抽水任务。作为上述领域创新技术的*供应商,我们是液体需要安全,高效和经济运输的*合作伙伴。

        德国凯森始终坚持“重质量,讲信誉”为宗旨。产品现畅销全国各地,并已逐步开发海外市场。公司多次被评为“重合同讲信用”企业,深得用户的信赖和广泛的赞誉。

        The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
          Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.