进口润滑油泵-进口油泵-德国KAYSEN泵业
| 货号 | KS5819569 |
|---|---|
| 品牌 | KAYSEN |
| 用途 | 抽水、化工、制药、石油、冶金、染料、冶炼、电力、电镀、农药、造纸、食品、纺织等行业酸洗工艺、制酸制碱、喷漆工艺、有色金属冶炼中的电解液输送、离子膜项目中的氯水输送、废水处理、电镀、农药领域。 |
| 型号 | KAYSEN |
| 工作压差 | 0 |
| 压力环境 | 常压 |
| 介质温度 | 250℃ |
| 驱动方式 | 电动 |
| 适用介质 | 水 |
润滑油泵-油泵-KAYSEN泵业
GERMANY KAYSEN PUMP CO .,LTD
润滑油泵主要用于各种机械设备中的润滑系统中输送润滑油。交流润滑油泵垂直安装在主油箱的顶板上，经 过油泵底部的滤网吸油，泵排油至主油泵进油管及 经冷油器至轴承润滑油母管，该泵由压力开关和装 在控制室内的三位开关控制，出口装有翻板式止逆 阀，防止油从系统中倒流。
主要特点：
●密封可靠，在长期运转中密封状态很稳定，泄露量很小。
●使用寿命长
●摩擦功率消耗小
●轴或轴套基本上不摩损；
●抗震性好，对旋转轴的振动以及轴对密封腔的偏斜不敏感；
●适用范围广，机械密封能用于高温，低温，高压，真空，不同旋转频率，以及各种腐蚀介质和含磨粒介质的密封。
主要应用：
可输送无润滑性的油料、饮料、低腐蚀性的液体。配用铜齿轮可输送低内点液体，如汽油、苯等。
润滑油故障排除：
| 现象 | 产生原因 | 排除方法 |
| 不排油或 排油少 | 1. 吸入高度太高超过额定值 2. 吸入管道漏气 3. 旋转方向不对 4. 吸入管道堵塞或阀门关闭 5. 液体温度低而使粘度增大 6. 齿轮与泵体麿损严重 | 1. 提高吸油面或减少管阻力 2. 检查各接合处是否漏气或漏液并加石棉等密封村料加以密封 3. 按泵的指示方向纠正转向 4. 清除堵塞物，开启阀门 5. 预热液体，如不可能则降低排出压力减少排油量 6. 拆卸检查有关另件并更换之 |
| 密封漏油 | 1. 轴封处未调整好 2. 密封圈磨损，间隙增大 3. 机械密封静环和动环的磨擦面损坏或有毛刺划痕等缺陷 4. 弹簧松驰 | 1. 重新调整 2. 造量拧紧螺母，或更换密封圈 3. 更换动静环或重新研磨 4. 更换弹簧 |
| 噪音或 振动大 | 1. 吸入网或滤网堵塞 2. 吸管伸入油池较浅 3. 管道进入空气 4. 排出管道阻力太大 5. 齿轮、轴承或侧板磨损严重 6. 吸入液体的粘度太大 | 1. 清除滤网上的污物 2. 吸入管应伸入油池0.5米左右 3. 检查各连接之处使之密封 4. 对管道和阀门进行检查，并排出堵塞之物，或调整管路减少弯头、阀门等 5. 更换新齿轮、轴承或侧板 6. 按第一段第六条处理 |
Lubricating oil pumps are mainly used to transport lubricating oil in lubrication systems in various mechanical equipment. The AC lubricating oil pump is vertically installed on the top plate of the main oil tank, sucks oil through the filter net at the bottom of the oil pump, and the pump discharges oil to the main oil pump inlet pipe and the oil cooler to the bearing lubricating oil main pipe, which is installed by the pressure switch and installed in the control room. The three-position switch is controlled, and the outlet is equipped with a flap type check valve to prevent oil from flowing back from the system.
main feature:
●The seal is reliable, the sealing state is stable during long-term operation, and the leakage is small.
●Long service life
● Friction power consumption is small
● The shaft or sleeve is basically not worn;
● good shock resistance, not sensitive to the vibration of the rotating shaft and the deflection of the shaft to the sealing chamber;
● Wide range of applications, mechanical seals can be used for high temperature, low temperature, high pressure, vacuum, different rotation frequency, as well as a variety of corrosive media and seals containing abrasive media.
main application:
It can transport non-lubricating oils, beverages and low corrosive liquids. With copper gears, it can transport low internal point liquids such as gasoline and benzene.
Lubricating oil troubleshooting:
Phenomenon Causes of elimination
No oil drain or low oil drain 1. Inhalation height is too high and exceeds rated value
2. Inhalation pipe leaks
3. The direction of rotation is wrong
4. The suction pipe is blocked or the valve is closed
5. The liquid temperature is low and the viscosity is increased
6. The gear and pump body are seriously damaged. 1. Increase the oil absorption surface or reduce the pipe resistance.
2. Check the joints for leaks or leaks and seal them with asbestos and other sealed materials.
3. Correct the steering according to the direction indicated by the pump
4. Clear the blockage and open the valve
5. Preheat the liquid, if not possible, reduce the discharge pressure and reduce the oil discharge.
6. Disassemble and inspect the relevant parts and replace them
Sealing oil leakage 1. The shaft seal is not adjusted
2. The seal is worn and the gap is increased
3. Mechanical seal static ring and moving ring friction surface damage or burr scratches and other defects
4. Spring relaxation 1. Readjust
2. Thread the nut or replace the seal
3. Replace the static ring or re-grind
4. Replace the spring
High noise or vibration 1. Jammed in the suction net or filter
2. The straw extends into the oil sump
3. Pipes enter the air
4. Exhaust pipe resistance is too high
5. Gears, bearings or side panels are severely worn
6. The viscosity of the inhaled liquid is too large 1. Remove the dirt from the filter net
2. The suction pipe should extend into the oil pool by about 0.5 meters.
3. Check each connection to seal it
4. Inspect pipes and valves, and discharge blocked objects, or adjust pipes to reduce elbows, valves, etc.
5. Replace new gears, bearings or side plates
6. Processed in accordance with Article 6 of the first paragraph
Cutting submersible sewage pump
Diving flow booster
Submersible mixed flow pump
Submersible return pump
Corrosion resistant sewage pump
Submersible mixer
位于Schw?bischGmünd的凯森Kaysen泵业有限公司是世界*的各种流体水泵和隔膜泵制造商之一。60多年来，凯森以“制造”的可靠性和质量达到了*标准。凭借我们全面的产品组合，我们支持世界各地的客户成功掌握供水，采矿，工业，化工，造纸，电力，食品，制药，污水和海上行业的苛刻抽水任务。作为上述领域创新技术的*供应商，我们是液体需要安全，高效和经济运输的*合作伙伴。
凯森始终坚持“重质量，讲信誉”为宗旨。产品现畅销全国各地，并已逐步开发海外市场。公司多次被评为“重合同讲信用”企业，深得用户的信赖和广泛的赞誉。
The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.
