进口潜水离心曝气机-进口潜水曝气机-德国KAYSEN泵业

进口潜水离心曝气机-进口潜水曝气机-德国KAYSEN泵业

产品介绍:

潜水离心曝气机-潜水曝气机-KAYSEN泵业GERMANY KAYSEN PUMP CO .,LTD潜水曝气机采用电机和叶轮直接传动,利用叶轮旋转所产生的离心力排开周围水形成低压区吸入水流同时,在叶轮处制造真空而吸入空气,在混气室中气与...


  • 物品单位:
  • 品牌: 德国KAYSEN
  • 货号: KS5895679

产品详细说明

货号 KS5895679
品牌 KAYSEN
用途 抽水、化工、制药、石油、冶金、染料、冶炼、电力、电镀、农药、造纸、食品、纺织等行业酸洗工艺、制酸制碱、喷漆工艺、有色金属冶炼中的电解液输送、离子膜项目中的氯水输送、废水处理、电镀、农药领域。
型号 KAYSEN
工作压差 0
压力环境 常压
介质温度 250℃
驱动方式 电动
适用介质

潜水离心曝气机-潜水曝气机-KAYSEN泵业

GERMANY KAYSEN PUMP CO .,LTD

潜水曝气机采用电机和叶轮直接传动,利用叶轮旋转所产生的离心力排开周围水形成低压区吸入水流同时,在叶轮处制造真空而吸入空气,在混气室中气与水充分混合形成均匀的气水混合液,在离心力作用下快速排出。
潜水离心式曝气机产品为自吸式曝气,直联式结构。旋转的叶轮产生的离心力,在叶轮的处形成负压吸入空气和水,利用叶轮的功能在混合室里将一定比例的气水混合,在强大的离心力下,气水二相流沿叶轮的切线方向经流道整流后,向圆周方向扩散,细碎的微小气泡充分与水相融,从而达到充氧曝气的效果。


主要特点:

主机潜水作业减少占地面积,噪音小;    
可直接在氧化塘中使用,节省基建成本;    
独立移动的曝气装置,曝气时兼有搅拌功能;    
底盘可根据用户要求作特殊设计。
自重定位,安装方便,可在不中断工艺运行的状态下自由布置
设计结构紧凑,利用自吸功能无需外接气源;  

 

主要应用:

潜水离心式曝气机用于各种污水处理工程中生化处理工艺的曝气池、曝气沉砂池、预曝气池、好氧硝化池曝气充氧混合及养殖塘增氧。


潜水曝气机注意事项:
1、如果水泵有任何小的故障切记不能让其工作。如果水泵轴的填料完磨损后要及时添加,如果继续使用水泵会漏气。这样带来的直接影响是电机耗能增加进而会损坏叶轮。  
2、如果水泵在使用的过程中发生强烈的震动这时一定要停下来检查下是什么原因,否则同样会对水泵造成损坏。  
3、当水泵底阀漏水时,有些人会用干土填入到水泵管里,用水冲到底阀处,这样的做法实在不可取。因为当把干土放入到进水管里当水泵开始工作时这些干土就会进入泵内,这时就会损坏水泵叶轮和轴承,这样做缩短了水泵使用寿命。当底阀漏水时一定要拿去维修,如果很严重那就需要更换新的。  
4、水泵使用后一定要注意保养,比如说当水泵用完后要把水泵里的水放干净,把水管卸下来然后用清水冲洗。  
5、水泵上的胶带也要卸下来,然后用水冲洗干净后在光照处晾干,不要把胶带放在阴暗潮湿的地方。水泵的胶带一定不能沾上油污,更不要在胶带上涂一些带粘性的东西。  
要仔细检查叶轮上是否有裂痕,叶轮固定在轴承上是否有松动,如果有出现裂缝和松动的现象要及时维修,如果水泵叶轮上面有泥土的也要清理干净。  无法启动  首先应检查电源供电情况:接头连接是否牢靠;开关接触是否紧密;保险丝是否熔断;三相供电的是否缺相等。如有断路、接触不良、保险丝熔断、缺相,应查明原因并及时进行修复。其次检查是否是水泵自身的机械故障,常见的原因有:填料太紧或叶轮与泵体之间被杂物卡住而堵塞;泵轴、轴承、减漏环锈住;泵轴严重弯曲等。排除方法:放松填料,疏通引水槽;拆开泵体清除杂物、除锈;拆下泵轴校正或更换新的泵轴。


Submersible jet aerator

Submersible aerator

Submersible centrifugal aerator



The submersible centrifugal aerator is directly driven by a motor and an impeller. The centrifugal force generated by the rotation of the impeller is used to discharge the surrounding water to form a low-pressure zone. At the same time, a vacuum is created at the inlet of the impeller to draw in air, and the gas and the water are thoroughly mixed in the mixing chamber. A uniform gas-water mixture is formed and rapidly discharged under the action of centrifugal force.

The submersible centrifugal aerator product is self-priming aeration and direct-connected structure. The centrifugal force generated by the rotating impeller forms a negative pressure at the inlet of the impeller to draw in air and water. The function of the impeller is used to mix a certain proportion of gas and water in the mixing chamber. Under strong centrifugal force, the gas-water two-phase flow along the impeller After the tangential direction is rectified by the flow path, it is diffused in the circumferential direction, and the finely divided fine bubbles are sufficiently fused with the water to achieve the effect of oxygenation and aeration.

 


main feature:


● Self-repositioning, easy to install, free to arrange without interrupting the process operation

●The design is compact, and the self-priming function does not require an external air source;

●The host diving operation reduces the floor space and the noise is small;

● It can be used directly in oxidation ponds to save infrastructure costs;

● Independently moving aeration device, which has a stirring function when aeration;

●The chassis can be specially designed according to user requirements.


 


main application:

The submersible centrifugal aerator is used for aeration tanks, aerated grit chambers, pre-aeration tanks, aerobic nitrification tanks, aeration and oxygenation mixing and aquaculture pond oxygenation in various sewage treatment projects.

       位于Schw?bischGmünd的凯森Kaysen泵业有限公司是世界*的各种流体水泵和隔膜泵制造商之一。60多年来,凯森以“制造”的可靠性和质量达到了*标准。凭借我们全面的产品组合,我们支持世界各地的客户成功掌握供水,采矿,工业,化工,造纸,电力,食品,制药,污水和海上行业的苛刻抽水任务。作为上述领域创新技术的*供应商,我们是液体需要安全,高效和经济运输的*合作伙伴。

        凯森始终坚持“重质量,讲信誉”为宗旨。产品现畅销全国各地,并已逐步开发海外市场。公司多次被评为“重合同讲信用”企业,深得用户的信赖和广泛的赞誉。

        The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
          Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.