GERMANY KAYSEN PUMP CO .,LTD
The imported hot water submersible pump is mainly suitable for extracting underground hot water for heating in winter, bathing, providing energy for industrial enterprises, and also can be used as industrial hot water circulation pump. Due to convenient installation, no basic investment is required, and it is accepted by the majority of users.
●It can extract high temperature hot water within 150 °C.
●The horizontal submersible pump can be used when the user needs it.
●Easy to install, put it in the sink and use it.
● It is not easy to enter the air, so there is no trouble in pumping.
●The motor adopts high temperature resistant waterproof wire, water lubrication, water cooling, and is not easy to pollute the environment.
● There is no need to build a pump house to save infrastructure investment.
● The running performance of the equipment is stable and the noise is extremely small.
It is suitable for geothermal, hot spring, metallurgy, chemical, textile, wood processing, papermaking, high temperature hot water pressurized circulation transportation of boilers, hotels, bathrooms, hotels, etc., as well as urban housing heating cycle pumps, using temperatures below 150 °C.
Maintenance of hot water submersible pumps:
● Regularly view consumables
First check the submersible pump, submersible pump, clean pump impeller, retaining ring, bushing, bearing housing and other wearing parts are not missing. Good can continue to be used, and bad ones need to be reassembled after replacing new qualified parts, and it is forbidden to use damaged and unqualified parts.
● Replace smooth oil
Open the oil hole screw inside the sealing chamber and the motor separately, and release the smooth oil in the sealed chamber and the motor inside to replace the new oil to ensure the normal operation of the smooth system.
● Guarantee submersible pump, submersible pump, clean water pump seal
When replacing the smooth oil in the sealed chamber, if the oil is found to be dirty and the water content has been exceeded, it is necessary to replace the integral sealing box or the dynamic and static sealing ring. The replacement parts need to be qualified products to ensure the sealing function.
●Removing moist moisture
For motor windings with insulation resistance values below 0.5 megohms, it is necessary to remove wet moisture. The drying method is the same as that of a normal motor. If the sealed box does not need to be replaced, it can only remove the stator part of the electric pump. Under normal circumstances, the sealed box part should be disassembled as much as possible. If it is really necessary to disassemble, it is necessary to replace the new "O" rubber seal ring. of.
●View submersible pump, submersible pump, clear water pump bearing
Look at the upper and lower bearings of the motor part. If it is found that the wear or the gap is too large, it is necessary to replace the new bearing in time, and it is forbidden to use it, so as to avoid further economic loss.
●Removal of the pump casing against rust
Before the spring application, the uppermost pump casing should be dismantled, and the impeller should be rolled and then closed to prevent the components from rusting and unable to start normally and burn the motor windings. This maintenance is especially important for water-filled motors.
● Ensure that the bearing is smooth
For the water-filled submersible pump, the skeleton oil seal and the lithium-based smooth grease of the upper and lower end cap bearing chambers should be replaced to ensure the normal operation of the bearing in a smooth and outstanding state for a long time.
Stainless steel hot spring pump
Long shaft deep well pump
Stainless steel deep well pump
Submersible electric pump
The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.