1
起批量(台) 价格
0 面议
供货能力: 电议 最低订购量: 1台
可销售总数量: 1000台
发布日期: 2019-10-11 更新日期: 2020-11-12
品牌: 德国KAYSEN 型号: KAYSEN
驱动方式: 电动 介质温度: 250 ℃
工作压差: 0 适用介质:
压力环境: 常压 货号: KS5819569
用途: 抽水、化工、制药、石油、冶金、染料、冶炼、电力、电镀、农药、造纸、食品、纺织等行业酸洗工艺、制酸制碱、喷漆工艺、有色金属冶炼中的电解液输送、离子膜项目中的氯水输送、废水处理、电镀、农药领域。 外型尺寸:

进口切割潜水排污泵-进口潜水排污泵-德国KAYSEN泵业

GERMANY KAYSEN PUMP CO .,LTD



进口切割潜水排污泵,是采用德国凯森泵业有限公司先进的技术研发而成水泵,此系列水泵具有带撕裂的结构,能将污水中长纤维、袋、带、草、布条等物质撕裂、切断,然后顺利排放,特别适合于输送含有坚硬固体、纤维物的液体以及特别脏、粘、滑的液体。
 

主要特点:

排污能力强、无堵塞,能有效通过直径φ30~φ80毫米的固体颗粒。

撕裂机构能够把纤维状物质撕裂,切断,然后顺利排放,无需在泵上加滤网。

设计合理,配套电机功率小,节能效果显著。

采用*材料的机械密封,可以使泵安全连续运行8000小时以上。

结构紧凑,移动方便,安装简单,无需建造泵房,减少工程造价。

双导轨自动安装系统,安装维修方便,人可不必为此而进出污水坑。

浮球开关可根据所需的水位变化,自动控制泵的停启,无需专人看管。

可配备全自动保护控制箱对产品的漏电、漏水及过载等进行有效保护,提高产品的安全可靠性。

 

主要应用:
进口切割潜水排污泵适用于化工、石油、制药、采矿、造纸、电厂及城市污水处理、市政工程、公共设施排污等输送带颗粒、纤维的污水污物。

切割潜水排污泵维护保养:
   ●电泵应有专人管理与使用,并定期检查电泵绕组与机壳之间的绝缘电阻是否正常*不得低于0.5兆欧,否则必须拆下将定子烘干,绝缘电阻升高后方可使用。
   ● 每次使用特别是用于较稠较粘的浆液后,应放于清水中运行数分钟再存放。
   ●电泵每使用300~500小时后应打开腰部油孔螺钉并用纯净10号机油补充,使用机械密封保持良好的润滑状态。如发现油室大量进水则表明机械密封失效,应予更换。
   ●电泵启动后如发现流量不足或扬程达不到规定值(除管路阻力大或堵塞)可能是转向反了,这时应断开电源,将电缆的三根相线中任意二根相互对换后,量新接好再启动便可。
   ●电泵拆卸、维修后,密封性能必须经0.2MPa气密试验检查。
   ●弯头和电泵分离放在板箱内,请将弯头装在电泵上,如果电果和管道连接则不必再装弯头。 


The imported cutting submersible sewage pump is a water pump developed by the advanced technology of Germany Kaisen Pump Co., Ltd. This series of pumps has a tearing structure, which can transport long fibers, bags, belts, grass, cloth and other materials in the sewage. It is torn, cut, and then discharged smoothly. It is especially suitable for conveying liquids containing hard solids and fibrous materials as well as particularly dirty, sticky and slippery liquids.

 


main feature:


● Strong discharge capacity, no clogging, and effective passage of solid particles with a diameter of φ30 to φ80 mm.


● The tearing mechanism can tear the fibrous material, cut it, and then discharge it smoothly without adding a strainer to the pump.


●The design is reasonable, the supporting motor power is small, and the energy saving effect is remarkable.


●The mechanical seal of the latest material can make the pump run safely for more than 8000 hours.


●Compact structure, easy to move, simple installation, no need to build pump room, reduce engineering cost.


●Double-rail automatic installation system, easy to install and maintain, people do not have to enter and exit the sump.


●Float switch can automatically control the pump to stop according to the required water level change, without special care.


● It can be equipped with fully automatic protection control box to effectively protect the product from leakage, water leakage and overload, and improve the safety and reliability of the product.


 


main application:

Imported cutting submersible sewage pump is suitable for chemical, petroleum, pharmaceutical, mining, paper, power plant and urban sewage treatment, municipal engineering, public facilities sewage and other conveyor belt particles, fiber sewage.


Cutting submersible sewage pump maintenance:

   ●The electric pump should be managed and used by special personnel, and regularly check whether the insulation resistance between the electric pump winding and the casing is normal and the minimum is not less than 0.5 megohm. Otherwise, the stator must be removed and the insulation resistance increased. .

   ● After each use, especially for thicker and more viscous slurry, it should be stored in clean water for a few minutes before storage.

   ● After using the electric pump for 300~500 hours, the lumbar oil hole screw should be opened and replenished with pure No. 10 oil, and the mechanical seal should be used to maintain a good lubrication state. If a large amount of water is found in the oil compartment, the mechanical seal is invalid and should be replaced.

   ●If the flow is insufficient or the lift does not reach the specified value after the start of the electric pump (except for the pipeline resistance or blockage), the steering may be reversed. At this time, the power should be disconnected, and any two of the three phases of the cable should be opposite each other. After the change, the new quantity can be connected and then started.

   ● After the electric pump is disassembled and repaired, the sealing performance must be checked by the 0.2MPa airtight test.

   ● The elbow and the electric pump are separated in the crates. Please install the elbow on the electric pump. If the electric fruit is connected with the pipe, it is not necessary to install the elbow.


Cutting submersible sewage pump

Diving flow booster

Submersible mixed flow pump

Submersible return pump

Corrosion resistant sewage pump

       位于德国Schw?bischGmünd的凯森Kaysen泵业有限公司是世界*的各种流体水泵和隔膜泵制造商之一。60多年来,凯森以“德国制造”的可靠性和质量达到了*标准。凭借我们全面的产品组合,我们支持世界各地的客户成功掌握供水,采矿,工业,化工,造纸,电力,食品,制药,污水和海上行业的苛刻抽水任务。作为上述领域创新技术的*供应商,我们是液体需要安全,高效和经济运输的*合作伙伴。

        德国凯森始终坚持“重质量,讲信誉”为宗旨。产品现畅销全国各地,并已逐步开发海外市场。公司多次被评为“重合同讲信用”企业,深得用户的信赖和广泛的赞誉。

        The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
          Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.