1
起批量(台) 价格
0 面议
供货能力: 电议 最低订购量: 1台
可销售总数量: 1000台
发布日期: 2019-10-12 更新日期: 2020-11-12
工作压差: 0 适用介质:
压力环境: 常压 货号: KS8538179
品牌: 德国KAYSEN 介质温度: 250 ℃
型号: KAYSEN 驱动方式: 电动
外型尺寸: 用途: 抽水、化工、制药、石油、冶金、染料、冶炼、电力、电镀、农药、造纸、食品、纺织等行业酸洗工艺、制酸制碱、喷漆工艺、有色金属冶炼中的电解液输送、离子膜项目中的氯水输送、废水处理、电镀、农药领域。

进口立式化工泵-进口化工泵-德国KAYSEN泵业

GERMANY KAYSEN PUMP CO .,LTD


进口立式化工离心泵,采用IH型离心泵之性能参数,在一般立式泵的基础上简化结构设计而成。根据使用温度、介质等不同在ISG型基础上派生出IHG型不锈钢化工泵。该系列产品的特点为结构紧凑,零配件种类少,使用和维修方便。


主要特点:

泵为立式结构,进出口口径相同,且位于同一中心线上,可象阀门一样安装于管路之中,外形紧凑,占地面积小,如加上电机防护罩则可置于户外使用。
叶轮直接安装在电机的加长轴上,轴向尺寸短。
轴封采用机械密封,根据介质可有不同的材质配置,能根据实际情况有效地延长机械密封的使用寿命。
安装检修方便,无需拆动管道路系统,只要卸下泵联体座螺母即可抽出全部转子部件。
可根据流量使用要求,采用并联运行方式。
可根据管路布置的要求采用泵的竖式和横式安装。

 

主要应用:
供输送不含固体颗粒(或者含微量细小颗粒,具体请咨询技术人员),具有一定腐蚀性,粘度类似于水的液体,被输送介质温度为-50℃~+150℃。广泛用于石油、化工、冶金、电力、造纸、烟气脱硫、除尘、食品制药和合成纤维等部门.

化工泵使用注意事项:
化工泵可根据不同的使用条件安装不同形式的机械密封,(如内装单端面平衡型和非平衡型,双端面平衡型及非平衡型,外装式机械密封等)。根据所选用密封型式的不同,其使用方法和注意事项也有所不同,具体情况请参阅机械密封安装使用说明书、GB3215-82“炼厂、化工及石油化工流程用离心泵通用技术条件",下面佰诺泵阀仅提几点一般应注意的事项。

  由于机械密封一般适用在清洁的,无悬浮颗粒的介质中使用,因此,对新安装的管路系统和储液灌,应认真冲洗干净,严防固体杂质进入机械密封端面而使密封失效。

  在易结晶的介质中,使用机械密封应注意经常冲洗。停车后重新起动前,要将机械密封上的结晶清洗干净。

  拆卸机械密封应仔细,不许用手锤,铁器等敲击,以免破坏动、静环密封面。

  如果有污垢拆不下来时,应设法清除污垢,冲洗干净后再进行拆卸,以免损坏密封元件。

  安装机械密封前,应检查所有密封元件是否有失效或损坏,如有则应重新修复或更换。

  应严格检查动环与静环的相对磨擦密封面,不允许有任何细微的划痕、碰伤等缺陷。所有另部件,包括泵体,叶轮,密封腔等在装配前均应冲洗干净,尤其是动、静环端面,要用清洁,柔软的布或棉纱认真擦拭干净,然后涂上一层清洁的油脂或机油。

  装配中要注意消除偏差,紧固螺钉时,要均匀拧紧,避免发生偏斜,使密封失效。

  正确调整弹簧的压缩量,泵安装好以后,以手扳动转子时,应感觉到密封弹簧既有一定的压缩量,而又能轻快、灵活地转动没有咬紧的感觉。如感觉太紧或盘不动,则应适当调松一些。

  IH化工泵对有外部冲洗的机械密封,起动前应先开启冲洗波,使密封腔内充满密封液。停车时,先停泵,后关密封冲洗液。


Corrosion resistant centrifugal pump

Vertical chemical pump

VChemical centrifugal pump



The imported vertical chemical centrifugal pump adopts the performance parameters of the IH centrifugal pump and is designed on the basis of the general vertical pump. IHG type stainless steel chemical pump is derived on the basis of ISG type according to the use temperature and medium. The series features compact structure, few spare parts, and easy to use and maintain.



main feature:


●The pump is of vertical structure, the inlet and outlet are the same diameter, and they are located on the same center line. They can be installed in the pipeline like a valve. The shape is compact and the footprint is small. If the motor protection cover is added, it can be placed outdoors. .

●The impeller is directly mounted on the extension shaft of the motor and has a short axial dimension.

●The shaft seal adopts mechanical seal. According to the medium, it can be configured with different materials, which can effectively extend the service life of the mechanical seal according to the actual situation.

●Easy to install and repair, no need to dismantle the pipe road system, just remove the pump joint nut to extract all the rotor parts.

● It can be operated in parallel according to the requirements of flow usage.

● The vertical and horizontal installation of the pump can be used according to the requirements of the pipeline arrangement.


main application:

For transport without solid particles (or containing traces of fine particles, please consult the technical staff), a certain corrosive, viscosity similar to water, the temperature of the medium being transported is -50 ° C ~ +150 ° C. Widely used in petroleum, chemical, metallurgy, electric power, paper, flue gas desulfurization, dust removal, food and pharmaceutical and synthetic fiber sectors.


Precautions for the use of chemical pumps:

The chemical pump can be installed with different types of mechanical seals according to different conditions of use (such as built-in single-end balanced and unbalanced type, double-end balanced and unbalanced type, external mechanical seal, etc.). According to the selected sealing type, the method of use and precautions are also different. For details, please refer to the mechanical seal installation and operation manual, GB3215-82 "General technical conditions for centrifugal pumps for refineries, chemical and petrochemical processes", below 佰The pump valve only mentions a few points that should be noted.


●Since the mechanical seal is generally suitable for use in clean, non-suspended particulate media, the newly installed piping system and liquid storage should be carefully rinsed to prevent solid impurities from entering the mechanical seal end face and causing the seal to fail.


● In a medium that is easy to crystallize, use a mechanical seal and pay attention to frequent flushing. The crystals on the mechanical seal should be cleaned before restarting after parking.


● Disassemble the mechanical seal carefully. Do not hit with a hammer or iron to avoid damaging the dynamic and static ring sealing surfaces.


● If there is dirt removed, try to remove the dirt, rinse it and then disassemble it to avoid damage to the sealing components.


● Before installing the mechanical seal, check all seal components for failure or damage, and if necessary, repair or replace them.


● The relative friction sealing surfaces of the moving ring and the stationary ring should be strictly checked. No slight scratches or bumps are allowed. All other parts, including the pump body, impeller, sealing chamber, etc. should be cleaned before assembly, especially the moving and static ring end faces. Wipe clean with a clean, soft cloth or cotton yarn, then apply a layer of clean grease. Or motor oil.


● Pay attention to eliminate the deviation during assembly. When tightening the screws, tighten them evenly to avoid deflection and invalidize the seal.


● Correctly adjust the compression amount of the spring. After the pump is installed, when the rotor is pulled by hand, the seal spring should be felt to have a certain amount of compression, and it can be lightly and flexibly rotated without the feeling of clenching. If you feel too tight or do not move, you should loosen some of them properly.


● IH chemical pump for mechanical seal with external flushing, the flushing wave should be turned on before starting, so that the sealing chamber is filled with sealing liquid. When parking, stop the pump first, then close the seal flushing fluid.


       位于德国Schw?bischGmünd的凯森Kaysen泵业有限公司是世界*的各种流体水泵和隔膜泵制造商之一。60多年来,凯森以“德国制造”的可靠性和质量达到了*标准。凭借我们全面的产品组合,我们支持世界各地的客户成功掌握供水,采矿,工业,化工,造纸,电力,食品,制药,污水和海上行业的苛刻抽水任务。作为上述领域创新技术的*供应商,我们是液体需要安全,高效和经济运输的*合作伙伴。

        德国凯森始终坚持“重质量,讲信誉”为宗旨。产品现畅销全国各地,并已逐步开发海外市场。公司多次被评为“重合同讲信用”企业,深得用户的信赖和广泛的赞誉。

        The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
          Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.