1
起批量(台) 价格
0 面议
供货能力: 电议 最低订购量: 1台
可销售总数量: 1000台
发布日期: 2020-07-16 更新日期: 2020-11-12
品牌: 德国KAYSEN 型号: KAYSEN
驱动方式: 气动 介质温度: 250 ℃
工作压差: 适用介质:
压力环境: 常压 货号:
用途: 水、化工、食品、颜料等 外型尺寸:

进口井用潜水泵


“ KAYSEN是工业行业的可靠解决方案合作伙伴,并且是化学液处理的组件和系统的制造商。基于我们的创新产品,服务和针对特定行业的解决方案,我们为全球客户提供了更高的效率和安全性。”

"Kaysen is a reliable solution partner for the industrial industry and a manufacturer of components and systems for chemical liquid treatment. Based on our innovative products, services and industry-specific solutions, we provide higher efficiency to customers worldwide And security."

进口井用潜水泵——上海总代理


我们的目标

为客户提高效率和安全性


我们在全球的市场水处理和化学流体处理


我们的报价 

组件,系统,服务和行业特定的解决方案


我们的价值

可靠性

革新

解决方案驱动

全球


Imported pneumatic diaphragm pump——Shanghai distributor


Our goal


Improve efficiency and safety for customers

Our global market water treatment and chemical fluid treatment


Our offer


Components, systems, services and industry-specific solutions



Our value


reliability


innovation


Solution driven


global



德国KAYSEN凯森进口井用深井泵概述

凯森井用潜水泵是深井提水的重要设备.使用时整个机组潜入水中工作.把地下水提取到地表,是生活用水.矿山抢险.工业冷却.农田灌溉.海水提升.轮船调载.还可用于喷泉景观.热水潜水泵用于温泉洗浴.居民小区利用地热采暖时可作为地热循环泵等,用途十分广泛. 该产品是地热开发利用工程的重要提水设备,耐热、防腐、抗老化,使用温度120℃,通过国家部级鉴定。潜水电机外壳采用不锈钢及锡青铜材料。


主要特点:

单级扬程高.单级泵壳高度矮.缩短了整机的高度增加了运行的稳定性。
泵轴直径远大于国标直径.为提取超级深井的地下水源增加了安全系数。
铸件采用HT200(普通铸件在HT150以下)超级深井泵壳采用球墨铸铁.铸钢.不锈钢来提高泵壳的承压系数。
逆止阀采用独特的设计方式.从根本上避免了超深井潜水泵.因停泵时回水水锤冲击力过大而造成的阀体断裂机组掉井的弊端。
轴向力小增加了电机的使用寿命。

主要优点:
具有结构紧凑
体积小
安装、使用维护方便
运输安全可靠
节约能源等优点
 

主要应用:
消防用抽水设备
供水干管
农业灌溉、矿场
地热水井
石化行业、具有腐蚀性和研磨性液体的化学系统
钢厂的热处理设施


井用潜水泵的维护和注意事项:
为了保证井用潜水泵装置的正常工作,减小故障率,延长使用寿命,平时必须加强对深井潜水泵的维修维护,定期对潜水泵及其控制系统进行全面的维护保养,每年至少做一次全面的预防性检修。
井用潜水泵使用中需要注意的维护与保养方法如下:
1、深井泵装置的使用环境应经常保持干燥。立式电动机表面应保持清洁,进风口不应受尘土、纤维等杂物的阻碍,保证风道畅通无阻。电动机周围不应放置热源,也尽量不要在户外直射阳光下使用,以免运行中过热造成损坏。
2、深井泵装置运行时,应经常注意有关仪表的读数,并定时记录水泵运行中的有关参数(如电动机的电压、
3、运行中如发现有任何不正常的响声,应立即停车进行检查。如发现电动机的防逆转装置失去作用时,必须进行检修,清楚污物,使其能良好地工作。
4、电动机控制装置的过电流保护或短路保护连续发生动作时,应检查故障是来自电动机过载还是保护装置定制太低。如果是保护装置的整定值太低,应调整保护装置的整定值至合理的数值;如果是因电动机过载造成,应及时检查电动机过载的原因,消除过载故障才可重新投入运行。
5、每次运行中因故停车时,应注意检查电动机油标的油位,如发现油位低于油标的一半时,应及时补充新油,以保证电动机角接触球轴承的可靠润滑。 


Overview of deep well pumps for imported wells from Kaysen in Germany

Kaysen well submersible pump is an important equipment for deep well water pumping. When in use, the entire unit is submerged into the water to work. The groundwater is extracted to the surface, which is domestic water. Mine emergency. Industrial cooling. Farmland irrigation. Seawater lifting. Fountain landscape. Hot water submersible pump is used for hot spring bathing. The residential area can be used as a geothermal circulation pump when using geothermal heating. It has a wide range of uses. This product is an important water lifting equipment for geothermal development and utilization projects. It is heat-resistant, anti-corrosive and anti-aging. The use temperature is 120℃, which has passed the national ministerial appraisal. The submersible motor housing is made of stainless steel and tin bronze.



main feature:

●Single-stage high head. Single-stage pump casing is short. Shorten the height of the whole machine and increase the stability of operation.

●The diameter of the pump shaft is much larger than the diameter of the national standard. It increases the safety factor for the extraction of groundwater sources in super deep wells.

●The casting adopts HT200 (ordinary casting is below HT150). The super deep well pump casing adopts ductile iron. Cast steel. Stainless steel to improve the pressure coefficient of the pump casing.

●The check valve adopts a unique design method. It fundamentally avoids the ultra-deep well submersible pump. The valve body fracture caused by the impact of the backwater hammer when the pump is stopped is too large.

●The small axial force increases the service life of the motor.


main advantage:

●Compact structure

●Small size

●Easy to install, use and maintain

●Safe and reliable transportation

●Energy saving and other advantages

 

main application:

●Fire pumping equipment

●Water supply mains

●Agricultural irrigation and mining

●Geothermal well

●Petrochemical industry, chemical systems with corrosive and abrasive liquids

●Heat treatment facilities in steel mills


Maintenance and precautions for well submersible pumps:

In order to ensure the normal operation of the submersible pump device for wells, reduce the failure rate, and extend the service life, it is necessary to strengthen the maintenance of the deep well submersible pumps, and carry out comprehensive maintenance of the submersible pumps and their control systems at least once a year. Preventive maintenance.

The maintenance and maintenance methods that need to be paid attention to in the use of well submersible pumps are as follows:

1. The operating environment of the deep well pump device should always be kept dry. The surface of the vertical motor should be kept clean, and the air inlet should not be hindered by dust, fibers and other debris to ensure that the air duct is unobstructed. No heat source should be placed around the motor, and try not to use it in direct sunlight outdoors to avoid damage caused by overheating during operation.

2. When the deep well pump device is in operation, you should always pay attention to the readings of related instruments and regularly record the relevant parameters of the pump during operation (such as the voltage of the motor,

3. If any abnormal noise is found during operation, stop immediately and check. If it is found that the anti-reverse device of the motor has failed, it must be repaired to clear the dirt and make it work well.

4. When the overcurrent protection or short circuit protection of the motor control device continues to operate, it should be checked whether the fault comes from the motor overload or the protection device is customized too low. If the setting value of the protection device is too low, the setting value of the protection device should be adjusted to a reasonable value; if it is caused by the motor overload, the cause of the motor overload should be checked in time, and the overload fault can be eliminated before it can be put into operation again.

5. Check the oil level of the motor oil mark when stopping for any reason during operation. If the oil level is found to be less than half of the oil mark, new oil should be added in time to ensure reliable lubrication of the motor angular contact ball bearings.


关于Kaysen


我们的基础

KAYSEN全球成功故事的基础是数十年来的工程专业知识,对应用的深刻理解和不断创新的高质量产品。因此,该公司集团不断投资于研发。KAYSEN在全球12个生产基地中也具有高度的垂直整合,从而确保为客户提供*的质量水平,并确保我们不受供应商市场波动的影响。


我们的宗旨

集成在精心设计的解决方案中的模块化KAYSEN系列,使我们各行各业的客户可以随时随地在其生产过程中实现*的安全性和效率。

对我们而言,与客户的亲近意味着与客户一起寻找适合个人需求的正确解决方案。个人,实用的建议和流畅的项目处理与我们全球客户服务一样,都是我们提供的服务的一部分。


我们的承诺

我们热情地致力于为每个客户选择合适的泵,可持续且具有成本效益的解决方案。

在90多个国家/地区,我们自己的销售,生产和服务公司的大约3,500名员工每天都在努力为每种产品提供快速可靠的服务。由于KAYSEN泵业作为全球市场*的地位,意味着对*产品和服务的持续承诺以及对负责任的思维和行动的义务。


Our foundation

KAYSEN's global success story is based on decades of engineering expertise, a deep understanding of applications and continuous innovation of high-quality products. As a result, the company group continuously invests in research and development. KAYSEN also has a high degree of vertical integration in 12 production bases around the world, thus ensuring to provide customers with an excellent level of quality and ensuring that we are not affected by supplier market fluctuations.


Our aim

The modular KAYSEN series integrated in carefully designed solutions enables our customers from all walks of life to achieve maximum safety and efficiency in their production processes anytime, anywhere.


For us, closeness to customers means working with customers to find the right solution for their individual needs. Personal, practical advice and smooth project handling are all part of the service we provide, just like our global customer service.


Our promise

We are passionately committed to choosing the right pump for each customer, sustainable and cost-effective solution.


In more than 90 countries, approximately 3,500 employees of our own sales, production and service companies work hard every day to provide fast and reliable service for each product. The status of KAYSEN Pumps as a global market leader implies a continuous commitment to excellent products and services and an obligation to responsible thinking and action.